徐州SKF轴承61852注脂的装置设计工艺

徐州SKF轴承不应该涂太多的油脂，我们知道油脂具有良好的附着力、耐磨性、耐温性、防锈性和润滑性，可以提高高温抗*氧化性，延缓老化，可以溶解碳，防止金属碎屑和油污的团聚，提高耐磨性和耐压性。伊斯坦斯伊斯坦斯止损。嗯，机械阻抗和耐腐蚀性。

Xuzhou SKF bearings should not be coated with too much grease. We know that grease has good adhesion, wear resistance, temperature resistance, rust resistance and lubricity. It can improve high temperature oxidation resistance, delay aging, dissolve carbon, prevent the agglomeration of metal debris and oil pollution, and improve wear resistance and pressure resistance. Istans Istans Stop Loss. Well, mechanical impedance and corrosion resistance.

因此，大量注脂对密封性能影响的实验证明，当注脂量小于轴承容积的30％时，由于轴承内不饱和油脂，润滑脂泄漏非常小。当徐州SKF轴承注脂量超过30个百分点时，轴承内部就会饱和。当润滑脂注入量达到50个百分点时，轴承中的润滑脂将完全饱和，过剩的润滑脂将被挤出。应当指出，虽然有时注脂是不够的，但注脂方法不够规范和科学，导致轴承腔内油含量不均匀，轴承局部饱和，以及早期的快速挤出现象。

Therefore, a large number of experiments on the effect of grease injection on sealing performance prove that when the grease injection volume is less than 30% of the bearing volume, the grease leakage is very ***all due to unsaturated grease in the bearing. When the grease injection of Xuzhou SKF bearings exceeds 30 percent, the inner part of the bearings will be saturated. When the grease injection reaches 50%, the grease in the bearing will be completely saturated and the excess grease will be extruded. It should be pointed out that although sometimes grease injection is not enough, the method of grease injection is not standardized and scientific enough, resulting in uneven oil content in the bearing chamber, local saturation of the bearing, and early rapid extrusion phenomenon.

轴承安装不是按照说明书和图纸做的，因为我们通常做生意，老师给你的，你所学的是方法，并没有遵循事实。当我们做任何事情时，我们可以选择徐州SKF轴承做我们想象中的事，总结我们的经验，以极大的耐力做生意，不怕被客户拒绝。所以对于我们常用的安装方法，我们可以总结出一套安装经验，今天的安农工程师总结了轴承装置的设计。

Bearing installation is not done according to the instructi*** and drawings, because we usually do business, the teacher g***e you, what you learned is the method, and did not follow the facts. When we do anything, we can choose Xuzhou SKF bearing to do what we imagine, sum up our experience, do business with great endurance, not afraid of rejection by customers. So for our commonly used installation methods, we can summarize a set of installation experience, today's Annong Engineer summarized the design of bearing device.

所谓轴承结构的设计过程，是指轴承轴的结构应尽可能简单，具有良好的加工装配工艺，减少劳动，提高劳动生产率，减少应力集中，提高轴的疲劳强度。

The so-called design process of bearing structure refers to that the structure of bearing shaft should be as simple as possible, h***e good processing and assembly technology, reduce labor, improve labor productivity, reduce stress concentration and improve the fatigue strength of the shaft.

在徐州SKF轴承装置的设计中，应尽可能准确地分析各种影响因素。然后对轴承的类型、结构和尺寸进行了选择，并考虑了其余方案的可能性。对轴承的技术参数、相关部件及润滑进行了选择。此外，还应考虑轴承的安装和维护。

In the design of Xuzhou SKF bearing device, various influencing factors should be analyzed as accurately as possible. Then the type, structure and size of the bearing are selected, and the possibility of other schemes is c***idered. The technical parameters, relevant components and lubrication of bearings are selected. In addition, bearing installation and maintenance should also be c***idered.

其次，针对其使用寿命长、可靠性高、经济性好的特点，建立了进口轴承结构。为了实现这个目标，设计工程师应该详细列出影响这些因素的因素以及必*须满足徐州SKF轴承的要求。在设计中，不仅要正确选择轴承类型、轴承结构和轴承结构，还要考虑轴承周围的部件，如轴、轴座、紧固件、密封件，尤其是润滑。所有这些因素都应该在生育率中加以考虑。

Secondly, aiming at its long service life, high reliability and good economy, the imported bearing structure is established. In order to achieve this goal, the design engineer should list in detail the factors affecting these factors and must meet the requirements of Xuzhou SKF bearings. In the design, not only the bearing type, bearing structure and bearing structure should be correctly selected, but also the components around the bearing, such as shaft, shaft seat, fasteners, seals, especially lubrication, should be c***idered. All these factors should be taken into account in fertility.

文章来自：徐州SKF轴承 www.wh-skf.com

文章来自：徐州INA轴承 www.ina-china.cn

文章来自：徐州NSK轴承 www.klbbearings.com

***：524085168

电话：0510-81207777

手机：13311666672/13395185757