泰州NSK轴承61904-Z定期维护排查的措施

在泰州NSK轴承转速上来说，轴承是根据轴承的类型，尺寸，精度，保持架类型，负荷，润滑方式，及冷却方式等因素确定。

In terms of the rotational speed of Taizhou NSK bearings, bearings are determined according to the type, size, accuracy, cage type, load, lubrication mode, and cooling mode of bearings.

轴承的安装及拆卸，在特定应用场合需要常常拆卸及安装，以确保可以按其地进行检测及维修。内外圈可以分别安装的轴承如：圆柱轴承，滚针轴承，及圆锥轴承十分合用于此场合。锥孔型的自动调心球泰州NSK轴承及自动调心滚子轴承在轴套的匡助下，同样简化了安装程序。

Bearing installation and disassembly, in specific applicati*** need to be often disassembled and installed to ensure that they can be inspected and maintained according to their location. Bearings such as cylindrical bearings, needle roller bearings and tapered bearings, which can be installed separately on the inner and outer rings, are very suitable for this occasion. Taizhou NSK bearing and automatic aligning roller bearing with taper pass can also simplify the installation procedure with the help of bushing.

在某些情况下滚动轴承要施加预压以增加刚性，此程序通常用于深沟球轴承、向心推力球轴承及圆锥滚子轴承内外圈偏置，轴弯曲，轴或轴承箱公差变化，配合错误都会导致内外圈的偏心。为防止偏心角渡过大，自动调心球轴承，自动调心滚子轴承，或调心轴承座是较佳的选择。嗓音频率及扭矩，动弹泰州NSK轴承都是根据高精度尺度出产制造的，所以嗓音及扭力小。深沟球轴承、及圆柱滚子轴承合用对于对低嗓音，低扭力有特别要求的场合。

In some cases, rolling bearings h***e to be preloaded to increase rigidity. This program is usually used for deep groove ball bearings, centripetal thrust ball bearings and tapered roller bearings with inner and outer rings offset, shaft bending, axle or bearing box tolerance changes, and mi***atch will lead to the eccentricity of inner and outer rings. In order to prevent excessive eccentricity, automatic self-aligning ball bearing, automatic self-aligning roller bearing or self-aligning bearing seat are better choices. The voice frequency and torsion, dynamic Taizhou NSK bearings are manufactured according to high precision scale, so the voice and torsion are ***all. Deep groove ball bearings and cylindrical roller bearings are used together for occasi*** with special requirements for low voice and low torsion.

(1)留意带密封轴承不可用本法清洗，密封的内部应坚持原样不可清洗。

(1) pay attention to the fact that sealed bearing can not be cleaned by this method, and the inside of the seal should be kept unclean.

(2)应将装配外表用干净的***、煤油、***或二***等溶液清洗干净，并用干净的抹布擦干，再涂上薄薄一层光滑油，这样可使装置操作起来便当效率。

(2) The assembly surface should be cleaned with clean gasoline, kerosene, toluene or xylene solution, wiped with a clean cloth, and then coated with a thin layer of ***ooth oil, so that the device can be operated easily and efficiently.

(3)临装置时翻开泰州NSK轴承封装，将它浸入上述***等液体中以手轻缓地转动，要保证坚持架，滚动体以及滚道外表的封装油彻底被清洗干净。

(3) When facing the device, open the package of Taizhou NSK bearing, immerse it in the above-mentioned gasoline and other liquids and rotate gently by hand, so as to ensure that the holder, rolling element and the packing oil on the raceway surface are thoroughly cleaned.

(4)清洗大量轴承时，先用温度为90～100℃的热机油淋烫以使封装油凝结，同时用无缝口且不落屑的工具挖净全部旧油，再淋烫几分钟，然后用煤油冲洗去机油，***后再用***清洗一遍。清洗干净后，应戴上薄膜手套将泰州NSK轴承放在工作台上的干净的布上或纸上晾干。

(4) When cleaning a large number of bearings, first use hot engine oil at 90-100 degrees Celsius to condensate the package oil, at the same time use seamless and non-chipping tools to dig out all the old oil, then rinse the oil with kerosene for a few minutes, and finally wash it with gasoline. After cleaning, wear thin film gloves to dry Taizhou NSK bearings on clean cloth or paper on the worktable.

文章来自：泰州SKF轴承 www.wh-skf.com

The article is from: Taizhou SKF bearing www.wh-skf.com

文章来自：泰州INA轴承 www.ina-china.cn

The article is from: Taizhou INA bearing www.ina-china.cn

文章来自：泰州NSK轴承 www.klbbearings.com

The article is from: Taizhou NSK bearing www.klbbearings.com

***：524085168

电话：0510-81207777

手机：13311666672