泰州NSK轴承61892修复案例展现不再束手无策

众所周知，泰州NSK轴承广泛应用于工业生产，但大多数人不知道他们会遇到什么问题，使用瑞典轴承。他们是无助的，不知道如何解决它们。让我告诉你。

As we all know, Taizhou NSK bearings are widely used in industrial production, but most people do not know what problems they will encounter, using Swedish bearings. They are helpless and do not know how to solve them. Let me tell you.

1。如果铁屑、毛刺、灰尘等***进入轴承，轴承在运行会产生振动和噪声，甚至损坏滚道和滚动。因此，在安装轴承之前，要确保设备的外观和设备环境的清洁。

1. If iron scraps, burrs, dust and other foreign bodies enter the bearing, the bearing will produce vibration and noise in operation, and even damage the raceway and rolling. Therefore, before installing the bearing, ensure the appearance of the equipment and the cleanliness of the equipment environment.

2。平滑度对轴承的使用寿命有非常重要的影响。这里简要介绍了选择润滑脂的一般标准。泰州NSK轴承光滑润滑脂由基础油、增稠剂和添加剂制成。不同类型和等级的润滑脂的性能有很大的不同。允许的旋转约束是不同的。选择润滑脂时应注意。润滑脂的性能主要取决于基础油。普通低粘度基础油适用于低温、高转速、高粘度基础油、高温、高负荷。增稠剂还与增稠剂的耐水性、增稠剂和防滑油的耐水性有关。根据这一标准，即使相同的增稠剂不能混合，不能混有不同等级的润滑油，因为不同的添加剂会对对方造成不同程度的影响。因此，选择光滑的润滑脂是非常重要的。

2. ***oothness has a very important effect on the service life of bearings. Here is a brief introduction to the general standard of choosing grease. Taizhou NSK bearing ***ooth grease is made from base oil, thickener and additive. The performance of different types and grades of grease is very different. The allowable rotation c***traints are different. Attention should be paid when choosing grease. The performance of grease depends mainly on base oil. Ordinary low viscosity base oil is suitable for low temperature, high speed, high viscosity base oil, high temperature and high load. Thickeners are also related to the water resistance of thickeners, thickeners and water resistance of antiskid oils. According to this standard, even if the same thickener can not be mixed, it can not be mixed with different grades of lubricants, because different additives will h***e different degrees of impact on each other. Therefore, it is very important to choose ***ooth grease.

三，光滑时，使用的油越多越好。这是一个普遍的误解。泰州NSK轴承和轴承腔过多的油脂导致过多的油混合，导致很高的温度。轴承填料的数量适合于轴承空间中的1/2至1/3填充，并应在高速下减少到1/3。所以，当我们增加石油时，我们须适度。

Three, when ***ooth, the more oil you use, the better. This is a common misunderstanding. Excessive grease in the NSK bearing and bearing chamber of Taizhou causes too much oil to mix, resulting in very high temperatures. The number of bearing packing is suitable for filling 1/2 to 1/3 in bearing space and should be reduced to 1/3 at high speed. So when we increase oil, we need to be moderate.

4。轴承上涂有防锈油。你须用干净的***或煤油清洗双手，然后用清洁、高速、高温润滑脂。清洁度对轴承寿命和振动噪声有很大影响。因此，在安装瑞典轴承时，须清洗。

4. The bearing is coated with antirust oil. You must wash your hands with clean gasoline or kerosene, then use clean, high-speed, high temperature grease. Cleanliness has great influence on bearing life and vibration noise. Therefore, when installing Swedish bearing, it must be cleaned.

5。安装时，不要直接锤击泰州NSK轴承端面和非应力表面。轴承应承受压块、套筒或其它装置的平均力。不通过滚动体动力传动装置。如果装置涂上光滑的油，它将使装置更加稳定。如果干扰严重，轴承应尽快在矿物油加热至80-90℃，和油的温度应严格控制，不得超过100℃，以防止回火硬度降低泰州NSK轴承和尺寸***的影响。当拆卸困难时，建议使用拆卸工具将地面拉入热油内圈。热会使轴承内圈收缩，使轴承更容易脱落。

5. When installing, do not directly hammer the Taizhou NSK bearing end face and the non stress surface. Bearing shall bear the ***erage force of pressing block, sleeve or other device. Not through the rolling body power tran***ission device. If the device is coated with ***ooth oil, it will make the device more stable. If the interference is serious, the bearing should be heated to 80-90 C in mineral oil as soon as possible, and the temperature of the oil should be strictly controlled, not exceeding 100 C, in order to prevent tempering hardness from reducing the impact of Taizhou NSK bearing and size recovery. When removal is difficult, it is recommended to use the disassembly tool to pull the ground into the inner ring of the hot oil. Heat will shrink the inner race of bearings and make bearings easier to fall off.

文章来自：泰州SKF轴承 www.wh-skf.com

The article is from: Taizhou SKF bearing www.wh-skf.com

文章来自：泰州INA轴承 www.ina-china.cn

The article is from: Taizhou INA bearing www.ina-china.cn

文章来自：泰州NSK轴承 www.klbbearings.com

The article is from: Taizhou NSK bearing www.klbbearings.com

***：524085168

电话：0510-81207777

手机：13311666672