测试温度对镇江NSK轴承6328润滑脂的变质效应

在进口轴承的使用中，润滑脂是非常重要的。如果使用改性润滑脂，不仅不能正常工作，而且会损坏轴承。

Grease is very important in the use of imported bearings. If the modified grease is used, it will not only fail to work normally, but will also damage the bearing.

1。油流观察：拿个量杯，一个装满了油来衡量的，其余是空的桌子上，与镇江NSK轴承润滑油的量杯，提升30-40厘米从表和倾斜，使润滑油慢慢进入空杯，观察其流动，质量好。润滑油的流动须是长的、均匀的、连续的。如果润滑油流动的快速和缓慢，有时大块会往下滑动，和润滑油会恶化。

1. Oil flow observation: take a measuring cup, one filled with oil to measure, the rest is empty table, with Zhenjiang NSK bearing lubricant measuring cup, 30-40 cm from the table and tilt, so that lubricant slowly into the empty cup, observe its flow, good quality. The flow of lubricating oil must be long, uniform and continuous. If the flow of oil is fast and slow, sometimes the block will slide down and the lubricating oil will deteriorate.

2。手撵法：润滑油摩擦反复拇指和食指之间，润滑剂感觉更好的润滑，磨屑少、无摩擦，如果手指与砂粒接触感觉摩擦力越大，表明更多的杂质。ES不能用于润滑油。应更用新的镇江NSK轴承润滑剂。

2. Pushing method: Lubricant rubbing repeatedly between thumb and index finger, lubricant feel better lubrication, less debris, no friction, if the finger contact with sand particles feel more friction, indicating more impurities. ES can not be used in lubricating oil. New Zhenjiang NSK bearing lubricants should be used more.

三。照明：在一个阳光充足的日子用螺丝刀从45度到一个水平面上拿起润滑剂。与太阳相比，在光油滴的观察，可以清楚地看到，在润滑油好，无杂质，可以继续发挥作用，如果有太多的杂质，应更换润滑油。

Three. Illumination: pick up lubricant on a sunny day with a screwdriver from 45 degrees to a horizontal plane. Compared with the sun, in the observation of oil droplets, it can be clearly seen that the lubricating oil is good, no impurities, can continue to play a role, if there are too many impurities, should replace the lubricating oil.

4。油滴***法：以干净的白色滤纸试纸，滴几滴滤纸油，润滑油的泄漏，如果黑粉的表面，用手触摸堵塞，说明镇江NSK轴承润滑油中的杂质较多，润滑效果好，无粉末，用手触摸干燥和变黑。

4. Oil drop tracing method: with clean white filter paper test paper, drop a few drops of filter paper oil, lubricant leakage, if the black powder surface, hand touch plugging, Zhenjiang NSK bearing lubricant in more impurities, lubrication effect is good, no powder, dry and blackened by hand touch.

让我们在对进口轴承温度的影响看，这通常表示轴承异常高温。高温对轴承润滑剂也是***的。有时轴承过热可归因于轴承的润滑剂。如果轴承温度超过125度，长期转移将降低轴承寿命。高温轴承的原因包括润滑不足或过度润滑，润滑剂。它含有杂质、过载、轴承损坏环、间隙不足和油封引起的高摩擦。

Let's take a look at the influence of the temperature on the imported bearing, which usually indicates the abnormal high temperature of the bearing. High temperature is also harmful to bearing lubricants. Sometimes the bearing overheat can be attributed to the lubricant of the bearing. If the bearing temperature exceeds 125 degrees, the long term transfer will reduce the bearing life. The reas*** for high temperature bearings include inadequate lubrication or excessive lubrication, lubricants. It contains impurities, overload, bearing damage ring, insufficient clearance and high friction caused by oil seal.

因此，无论是镇江NSK轴承本身或其余的重要组成部分，它需要不断监测进口轴承的温度。如果操作条件保持不变，温度的任何变化都可以指示故障。

Therefore, whether it is Zhenjiang NSK bearing itself or other important components, it needs to continuously monitor the temperature of imported bearings. If the operating conditi*** remain unchanged, any change in temperature can indicate failure.

进口轴承的温度循环可以用温度计，如数字温度计，能准确测量进口轴承的温度，可以在一个显示单元。华氏温度或华氏温度。重要的是，进口轴承，损坏时，会造成设备的停机，因此这种镇江NSK轴承应安装温度探测器。

Imported bearing temperature cycle can be used thermometer, such as digital thermometer, can accurately measure the temperature of the imported bearing, can be in a display unit. Fahrenheit or Fahrenheit. Importantly, the imported bearings, when damaged, will cause equipment shutdown, so this Zhenjiang NSK bearings should be installed temperature detector.

文章来自：镇江SKF轴承 www.wh-skf.com

The article is from: Zhenjiang SKF bearing www.wh-skf.com

文章来自：镇江INA轴承 www.ina-china.cn

The article is from: Zhenjiang INA bearing www.ina-china.cn

文章来自：镇江NSK轴承 www.klbbearings.com

The article is from: Zhenjiang NSK bearing www.klbbearings.com

***：524085168

电话：0510-81207777

手机：13311666672