南京INA轴承现象级损伤的维修对策

首先，在南京INA轴承环境中应进行光环境检查，是像散，以便更好地观察轴承的外表面，看其表面无裂纹等异常。例如，在机械云的形成中，磨损、划伤和凸出将导致轴承装置的偏离，导致装置位置，导致载荷平滑和应力集中，降低轴承成形精度和使用寿命。

First of all, in Nanjing INA bearing environment should be carried out light environment inspection, astigmati***, in order to better observe the bearing's external surface, see its surface without cracks and other abnormalities. For example, in the formation of mechanical clouds, wear, scratch and protrusion will lead to the deviation of the bearing device, leading to the location of the device, resulting in load ***oothing and stress concentration, reducing the bearing forming accuracy and service life.

南京INA轴承的维护、修理和异常处理

Maintenance, repair and exception handling of INA bearings in Nanjing

为了尽可能长时间地保持轴承的原始性能，有必要对轴承进行维修，以防止今后发生事故，保证运行的可靠性，提高生产率和经济性。保持相应的机械操作条件的操作标准并定期执行。内容包括润滑油的监测、补充或更换和定期拆卸检查。

In order to maintain the original performance of bearings as long as possible, it is necessary to maintain the bearings to prevent future accidents, ensure the reliability of operation, improve productivity and economy. Maintain appropriate operating standa*** for mechanical operation conditi*** and perform them regularly. The contents include monitoring, replenishment or replacement of lubricating oil and regular disassembly inspection.

作为南京INA轴承维修项目，有旋转声、振动、温度、润滑剂状态等。

As a INA bearing maintenance project in Nanjing, there are rotating sound, vibration, temperature, lubricant state and so on.

轴承损坏及对策

Bearing damage and Countermeasures

一般来说，如果轴承使用得当，就可以使用，直到达到疲劳寿命。但事故发生得太早，不会受到损坏。这种早期损坏，相对于疲劳寿命，使用质量作为一个故障或事故。由于忽略了安装、使用和润滑，南京INA轴承和壳体的热效应由于外来材料的***而没有很好的研究。

Generally speaking, if the bearing is used properly, it can be used until the fatigue life is reached. But the accident happened too early and it would not be damaged. This early damage, relative to fatigue life, uses mass as a fault or accident. Due to neglect of installation, use and lubrication, the thermal effect of Nanjing INA bearing and shell has not been well studied due to the invasion of foreign materials.

有些企业环境条件差，空气中***物质含量高，周转场所小，难以进行防锈处理。除了炎热天气外，生产工人违反了防锈条例。

Some enterprises h***e poor environmental conditi***, high content of harmful substances in the air, and ***all turnover places, so it is difficult to carry out anti-rust treatment. In addition to the hot weather, the production workers violated the rust prevention regulati***.

一些企业的防锈纸、尼龙纸（袋）和塑料缸轴承包装材料不符合滚动南京INA轴承油封防锈包装的要求也是造成锈蚀的因素之一。

Some enterprises'rust-proof paper, nylon paper (bag) and plastic cylinder bearing packaging materials do not meet the requirements of rolling Nanjing INA bearing oil seal rust-proof packaging is also one of the factors causing rust.

部分企业轴承套圈的车削余量和磨削余量小，外圆上的氧化皮和脱碳层不能完全去除。罐笼的HJ是好还是坏。HJ点是否太小，HJ不牢固，或HJ过多导致球问题。它们都是轴承检查时需要特别注意的地方。还有其余问题需要注意。

The turning allowance and grinding allowance of bearing rings in some enterprises are ***all, and the oxide scale and decarbonization layer on the outer circle can not be completely removed. The HJ of the cage is good or bad. HJ point is too ***all, HJ is not strong, or too much HJ cause the ball problem. They are all places that need special attention when bearing inspection. There are other problems to note.

文章来自：南京SKF轴承 www.wh-skf.com

The article is from: Nanjing SKF bearing www.wh-skf.com

文章来自：南京INA轴承 www.ina-china.cn

The article is from: Nanjing INA bearing www.ina-china.cn

文章来自：南京NSK轴承 www.klbbearings.com

The article is from: Nanjing NSK bearing www.klbbearings.com