南京SKF轴承磁力分类的检修与***

磁力轴承也是一种滚动轴承，每种磁力轴承的控制方法、结构、磁能都不同，所以如果你想对南京SKF轴承磁力系列进行分类，你可以根据这些因素进行分类。

Magnetic bearing is also a kind of rolling bearing, each magnetic bearing control method, structure, magnetic energy are different, so if you want to classify the Nanjing SKF bearing magnetic series, you can classify according to these factors.

对几个轴承的吸引力有特别的约束。因此，他们具有开发、生产和应用各种***工程产品的常识和业界知识。小型轴承，如微型轴承，只有0.003克，大轴承高达30~40t。同时，永磁轴承只能是被动的，被动轴承不能在所有三个方向稳定，至少一个方向应选择为主动；直流励磁轴承只能主动（自动）；排斥磁轴承，因为磁利用。它很低。力，结构比吸力更混乱，很少使用。等待。

There are special restricti*** on the attractiveness of several bearings. Therefore, they h***e the common sense and knowledge of developing, producing and applying all kinds of advanced engineering products. ***all bearings, such as miniature bearings, are only 0.003 grams, with large bearings up to 30~40t. At the same time, permanent magnet bearings can only be passive, passive bearings can not be stable in all three directi***, at least one direction should be chosen as active; DC excitation bearings can only be active (automatic); repel magnetic bearings, because of magnetic utilization. It's very low. Force, structure is more chaotic than suction and seldom used. Wait.

使用南京SKF轴承时一定要注意轴的保护和***过程，我会向大家解释（一个接一个）关于轴的维护，希望对大家有所帮助。

Nanjing SKF bearings must pay attention to the use of shaft protection and maintenance process, I will explain to you (one after another) about shaft maintenance, I hope to help you.

传动轴的维修方法如下：

The maintenance methods of the tran***ission shaft are as follows:

1，对于后轮驱动车辆，驱动轴由两个不稳定的关节组成。如果当汽车启动或加速或减速时，从汽车底部单击释放离合器，这意味着更换联轴器。

1, for rear wheel drive vehicles, the drive shaft c***ists of two unstable joints. If you click the release clutch from the bottom of the car when the car starts or accelerates or decelerates, that means replacing the coupling.

2。将传动轴保持在汽车下方，并将其摇晃到左右。如果旋转角度超过45度，则意味着非等速万向节之间的间隙太大，无法***。

2. Keep the tran***ission shaft under the car and shake it to the left and right. If the rotation angle exceeds 45 degrees, it means that the clearance between the non-c***tant speed universal joints is too large to be restored.

3。轮驱动车辆传动轴采用等速万向节，接头部分采用橡胶套密封。车主须定期检查南京SKF轴承橡胶套的状况。砂子一旦损坏，在运行过程中会与万向节发生碰撞，加速磨损（基本零件失效），缩短使用寿命。

3. The wheel drive vehicle tran***ission shaft adopts c***tant velocity universal joint, and the joint part is sealed by rubber sleeve. Owners should regularly check the status of SKF bearing rubber sleeves in Nanjing. Once the sand is damaged, it will collide with the universal joint during operation, accelerate wear and tear (failure of basic parts), and shorten the service life.

4。检查橡胶套是否开裂非常简单：如果在发动机轮辋和底部附近发现非常粘的润滑脂，或者在行驶过程中方向盘是否被触摸，将会出现裂纹，表明万向节已经损坏并且应该更换。

4. It is very simple to check if the rubber sleeve is cracked: if very sticky grease is found near the rim and bottom of the engine, or if the steering wheel is touched during driving, there will be cracks indicating that the universal joint has been damaged and should be replaced.

5。车主应尽量避免撞在方向盘原地，因为这将导致万向节由于超载和缩短寿命。

5. Car owners should try to ***oid hitting the steering wheel in situ, as this will lead to the universal joint due to overload and shorten the life.

南京SKF轴承传动轴的保护方法如下：

The protection methods of Nanjing SKF bearing drive shaft are as follows:

1，严禁高齿轮起动。他在轴承行业有着丰富的经验，并且具有开发、制造和使用各种***工程产品所需的知识和专长。

1, high gear starting is strictly prohibited. He has a wealth of experience in the bearing industry, and has the knowledge and expertise required to develop, manufacture and use a variety of advanced engineering products.

2，不要松开离合器踏板。

2, do not loosen the clutch pedal.

3，禁止超载和速度极限行驶。

3, prohibit overload and speed limit.

4。定期检查传动轴的工作状态。

4. Check the working status of the tran***ission shaft regularly.

5。有必要检查南京SKF轴承传动轴钩的紧固、支承橡胶是否损坏、传动轴关节是否松动、传动轴是否变形。

5. It is necessary to check the fastening of Nanjing SKF bearing tran***ission shaft hook, whether the supporting rubber is damaged, whether the tran***ission shaft joint is loose, whether the tran***ission shaft is deformed.

6、为了保证传动轴的动态平衡，应始终注意平衡垫是否拆卸。

6, in order to ensure the dynamic balance of the tran***ission shaft, we should always pay attention to whether the balance pad is di***antled.

文章来自：南京SKF轴承 www.wh-skf.com

The article is from: Nanjing SKF bearing www.wh-skf.com

文章来自：南京INA轴承 www.ina-china.cn

The article is from: Nanjing INA bearing www.ina-china.cn

文章来自：南京NSK轴承 www.klbbearings.com

The article is from: Nanjing NSK bearing www.klbbearings.com

***：524085168

电话：0510-81207777

手机：13311666672