南京NSK轴承振动磨损不可忽略的次要因素

1，南京NSK轴承将内部节余节省到外部节余，并增加压力表，以显示上下腔室压力是瞬时的。通过这种方式，贴片保护方便且易于定期清洗，这与内部省煤器是***的。

1. Nanjing NSK bearings s***e internal s***ings to external s***ings and add pressure gauges to show that the upper and lower chamber pressure is instantaneous. In this way, patch protection is convenient and easy to clean regularly, which is incomparable with the internal economizer.

2，节省比。比率一般在1.2到1.5之间。根据多年的经验，更好的应该是维持在1.25上下。为了保证β值，在南京NSK轴承主轴、前后轴套的保护与维护中，需严格控制精度、同轴度、圆度和锥度。

2, s***ing ratio. The ratio is usually between 1.2 and 1.5. Based on many years of experience, it should be maintained at 1.25. In order to ensure the beta value, the precision, coaxiality, roundness and taper must be strictly controlled in the protection and maintenance of the main shaft and front and rear axle sleeve of Nanjing NSK bearing.

3，当主轴没有安装在每个空腔中时，每个南京NSK轴承出口处的油柱必是共同的。如果不是，则应使用改变省煤器直径的方法来改变流量。轴承具有广泛的现场经验，因此具有开发、制造和使用***工程产品的必要知识和专门知识。小型轴承，如微型轴承，只有0.003克，大轴承高达三四万千克。

3. When the spindle is not installed in each c***ity, the oil column at the outlet of each Nanjing NSK bearing must be common. If not, the method of changing the diameter of the economizer should be used to change the flow rate. Bearings h***e extensive field experience and therefore h***e the necessary knowledge and expertise to develop, manufacture and use advanced engineering products. ***all bearings, such as miniature bearings, are only 0.003 grams, and large bearings are as high as thirty thousand or forty thousand kilograms.

在滚动南京NSK轴承中，外圈安装在轴承座孔中，通常不旋转，但是当与轴匹配时，它与轴一起旋转。滚动轴承使用和维护非常方便，任务的功能非常可靠。然而，这是不可避免的随着时间的推移，因为一些固有的元素可能是固有的，造成损坏或磨损。

In rolling Nanjing NSK bearings, the outer ring is mounted in the bearing seat bore and usually does not rotate, but when matched with the shaft, it rotates with the shaft. Rolling bearing is very convenient to use and maintain, and the function of the task is very reliable. However, this is inevitable over time because some inherent elements may be inherent, causing damage or wear.

滚动轴承有许多磨损形式，如磨粒磨损、微动磨损、粘着磨损、腐蚀磨损等。磨损的原因有：

There are many wear forms of rolling bearings, such as abrasive wear, fretting wear, adhesive wear, corrosion wear and so on. The reas*** for wear are:

1，稳定性差。在这种情况下，南京NSK轴承相对运动的出现更容易引起粘连、磨损甚至温度过高损伤。

1, poor stability. In this case, the relative motion of Nanjing NSK bearings is more likely to cause adhesion, wear and even excessive temperature damage.

2，灰尘进入轴承，平滑剂（作用：可增加或防止摩擦磨损）中含有杂质，轴承清洗不干净，就会发生磨损；

2, dust into the bearing, ***oothing agent (role: can increase or prevent friction and wear) contains impurities, bearing cleaning is not clean, will occur wear;

3，湿式、湿式和酸性溶液腐蚀轴承，造成腐蚀和磨损。

3, wet, wet and acidic soluti*** corrode bearings, causing corrosion and wear.

4，轴承在大的振动下不会旋转和暂时振动，这将引起微动磨损。轴承是消耗品南京NSK轴承。轴承在***轴承行业，坚持引导地位。标准货品供应超过20000种轴承。

4, the bearing will not rotate and temporarily vibrate under large vibration, which will cause fretting wear. Bearing is c***umable Nanjing NSK bearing. Bearing in the global bearing industry, adhere to the guiding position. Standard goods supply more than 20000 kinds of bearings.

文章来自：南京SKF轴承 www.wh-skf.com

The article is from: Nanjing SKF bearing www.wh-skf.com

文章来自：南京INA轴承 www.ina-china.cn

The article is from: Nanjing INA bearing www.ina-china.cn

文章来自：南京NSK轴承 www.klbbearings.com

The article is from: Nanjing NSK bearing www.klbbearings.com

***：524085168  

电话：0510-81207777

手机：13311666672