南京INA轴承螺旋系列产品的优缺共鸣

1。螺旋南京INA轴承由弹簧钢制成。弹簧钢的温度敏***低于1800℃退火的球轴承钢（100C6），当回火温度达到回火温度时，材料将失去其硬度。因此，弹簧钢更适合高温操作。

1. The spiral INA bearing of Nanjing is made of spring steel. The temperature sensitivity of spring steel is lower than that of ball bearing steel (100C6) annealed at 1800 C. When tempering temperature reaches tempering temperature, the material will lose its hardness. Therefore, spring steel is more suitable for high temperature operation.

2。螺旋南京INA轴承是耐用的，不受灰尘、铁屑、水和弱酸的影响，通过铁粉和水的滴落而形成。薄壁螺旋环为大直径轧制零件留下了较大的空间。这些部件可以通过轧制轧制成螺旋槽。这使得轴承在旋转过程中保持清洁。

2. The spiral Nanjing INA bearing is durable, free from dust, iron chips, water and weak acid, formed by dropping iron powder and water. The thin wall spiral ring left a larger space for the large diameter rolling parts. These components can be rolled into spiral grooves by rolling. This keeps the bearings clean during rotation.

3。弹簧***性好，安装方便。内环可通过两个钩扳手安装在任何位置。内圈的内张力可以固定在南京INA轴承轴上。使用弹性材料可以容易地实现具有H9或H1L公差的内环。这种昂贵的处理成本可以在内环中分配。

3. Spring steel has good elasticity and easy installation. The inner ring can be installed in any position by two hook wrenches. The inner tension of the inner ring can be fixed on the INA bearing shaft of Nanjing. The inner ring with H9 or H1L tolerance can be easily realized by using elastic material. This expensive processing cost can be allocated in the inner loop.

4。螺旋南京INA轴承的主要优点是外圈可以重复使用多次，这使得它一旦损坏和翘曲就可以重新加工。在这种情况下，轴承壳体也需要调整。这种结构的设计只需要改变螺杆的外环，而不是改变整个轴承，所有其它轴承部件都可以重复使用。南京INA轴承块的调整是通过增加1毫米的直径来实现的。例如，当内径从105mm增加到106 mm时，螺旋外环的外径也需要通过安装LMM来增加。这可以重复，直到直径达到110毫米。轴承外圈可加工5次。这可以节省很多钱，特别是如果所有其他轴承部件可以重复使用六次。

4. The main advantage of the spiral Nanjing INA bearing is that the outer ring can be reused many times, which allows it to be reprocessed once damaged and warped. In this case, the bearing housing also needs to be adjusted. The design of this structure only needs to change the outer ring of the screw, not the entire bearing, and all other bearing parts can be reused. The adjustment of Nanjing INA bearing block is achieved by increasing the diameter of 1 mm. For example, when the inner diameter increases from 105mm to 106 mm, the outer diameter of the spiral outer ring also needs to be increased by installing LMM. This can be repeated until the diameter reaches 110 mm. Bearing outer ring can be machined 5 times. This can s***e a lot of money, especially if all other bearing parts can be reused six times.

文章来自：南京SKF轴承 www.wh-skf.com

The article is from: Nanjing SKF bearing www.wh-skf.com

文章来自：南京INA轴承 www.ina-china.cn

The article is from: Nanjing INA bearing www.ina-china.cn

文章来自：南京NSK轴承 www.klbbearings.com

The article is from: Nanjing NSK bearing www.klbbearings.com

***：524085168  

电话：0510-81207777

手机：13311666672