扬州NSK轴承圆锥孔感应加热的装置

除扬州NSK轴承使用热油外，该装置还广泛应用于电磁感应中。

In addition to hot oil used in NSK bearings in Yangzhou, the device is also widely used in electromagnetic induction.

感应加热装置配备有励磁线圈。在扬州NSK轴承电磁感应之后，电流流向加热体（周成），并通过周成本身的阻抗产生热量。因此，可以在短时间内不用火和油均匀加热。轴承热负荷高、清洁。

The induction heating device is equipped with an excitation coil. After the electromagnetic induction of NSK bearing in Yangzhou, the current flows to the heating body (Zhou Cheng) and generates heat through the impedance of Zhou Cheng itself. Therefore, it can be heated evenly without fire and oil in a short time. The heat load of the bearing is high and clean.

内环的安装和拆卸可用于扬州NSK轴承的特殊感应加热装置，如铁路车辆轴箱中的滚柱轴承和圆柱滚子轴承。

The installation and di***antling of the inner ring can be used for special induction heating devices of Yangzhou NSK bearings, such as roller bearings and cylindrical roller bearings in railway vehicle axle boxes.

圆锥孔轴承的安装

Installation of conical bore bearing

锥形孔扬州NSK轴承直接将内圈固定在圆锥轴上，或使用密封套筒和可拆卸套筒安装在圆柱形轴上。

The tapered bore Yangzhou NSK bearing directly attaches the inner ring to the conical shaft, or uses a sealed sleeve and a detachable sleeve to be installed on the cylindrical shaft.

大型自动调心滚子扬州NSK轴承装有多个液压系统。使用液压螺母压缩套筒的例子。当高压油被压入配合表面并将螺栓压入装配套筒时在密封套筒上安装油孔的方法。

Large automatic roller bearings Yangzhou NSK bearings are equipped with multiple hydraulic systems. An example of using a hydraulic nut to compress the sleeve. When the high pressure oil is pressed into the mating surface and the bolt is pressed into the assembly sleeve, an oil hole method is installed on the sealing sleeve.

中心扬州NSK轴承的压力入口参考表。检查径向间隙的减少和安装。使用塞尺测量间隙，应同时测量两列的***小值。

Center Yangzhou NSK bearing pressure inlet reference table. Check the reduction and installation of radial clearance. Using the feeler gauge to measure the clearance, the minimum value of the two column should be measured at the same time.

由于扬州NSK轴承的尺寸被扩大并安装在轴上，由于自重外环的椭圆变形和轴承底部的间隙的测量，测量将大于实际间隙。扬州NSK轴承径向间隙的误差将按照近似标准安装，这将造成过多的干扰或实际安装间隙太小。因此，如所示，两个水平间隙A、B和底部间隙C的一半被视为间隙。

Because the size of the Yangzhou NSK bearing is enlarged and installed on the shaft, the measurement will be greater than the actual clearance due to the elliptical deformation of the self - weight outer ring and the measurement of the gap at the bottom of the bearing. The error of Yangzhou NSK bearing radial clearance will be installed according to the approximate standard, which will cause too much interference or the actual installation clearance is too ***all. Therefore, as shown, half of the two horizontal gaps A, B and bottom clearance C are regarded as gaps.

在轴承布什上安装滚珠轴承时，外圈可灵活调整，安装后的间隙不应太小。

When ball bearings are installed on bearing Bush, the outer ring can be adjusted flexibly, and the clearance after installation should not be too ***all.

文章来自：扬州SKF轴承 www.wh-skf.com

The article comes from: Yangzhou SKF bearing www.wh-skf.com

文章来自：扬州INA轴承 www.ina-china.cn

The article comes from: Yangzhou INA bearing www.ina-china.cn

文章来自：扬州NSK轴承 www.klbbearings.com

The article comes from: Yangzhou NSK bearing www.klbbearings.com

***：524085168  

电话：0510-81207777

手机：13311666672