扬州NSK轴承安装操作的规范性

当器件到达外壳时，一般的间隙适合于许多器件。外圈受到干扰，通常通过压制或冷却来安装扬州NSK轴承的冷收缩配合方法。干冰被用作冷却剂，并配有冷收缩配合。空气中的水凝结在进口轴承的表面上。因此，有必要采取适当措施防止扬州NSK轴承的沙沙。

When the device reaches the shell, the general gap is suitable for many devices. The external ring is disturbed, usually by pressing or cooling to install the cold shrink fit method of Yangzhou NSK bearing. Dry ice is used as coolant and equipped with cold shrink fit. The water in the air condenses on the surface of the imported bearing. Therefore, it is necessary to take appropriate measures to prevent the NSK bearing from rustling in Yangzhou.

它影响了NSK轴承在扬州的精度、寿命和性能。因此，进口轴承设备：进口轴承设备是正确的。设计和装配部门应充分研究进口轴承的设备。希望该装置按照操作规范进行。项目的规格通常如下：

It affects the accuracy, life and performance of NSK bearings in Yangzhou. Therefore, imported bearing equipment: imported bearing equipment is correct. The design and assembly department should fully study the equipment of imported bearings. It is hoped that the device will be carried out according to the operation specification. The specificati*** of the project are usually as follows:

1清洁扬州NSK轴承和进口轴承相关零件；

1 clean Yangzhou NSK bearing and import bearing related parts;

2检查连接器的尺寸和完成情况。

2 check the size and completion of the connector.

3器件；

3 devices;

4扬州NSK轴承检查；

4 Yangzhou NSK bearing inspection;

5供应润滑剂。

5 supply lubricants.

只有打开扬州NSK轴承包装。一般油脂润滑，希望在设备准备好之前。不干净，直走。润滑油是润滑的，不需要清洗。然而，清洗油被应用到仪表或高速进口轴承上，并且去除了应用于进口轴承的防锈剂。

Only open the Yangzhou NSK bearing packaging. General grease lubrication, hopefully before the equipment is ready. Not clean, go straight. The lubricating oil is lubricated and does not need to be cleaned. However, the cleaning oil is applied to the instrument or the high speed imported bearing, and the rust inhibitor applied to the imported bearing is removed.

扬州NSK轴承除锈剂易生锈，不可忽视。此外，进口润滑脂密封轴承不直接清洗和直接使用。进口轴承的安装方法不同于进口轴承的结构、协调和条件。通常，由于轴的转动，扬州NSK轴承的内圈需要过盈配合。

Yangzhou NSK bearing rust remover is easy to rust and can not be ignored. In addition, imported grease seal bearings are not directly cleaned and used directly. The installation method of imported bearings is different from the structure, coordination and conditi*** of imported bearings. Usually, due to the rotation of the shaft, the inner ring of Yangzhou NSK bearing needs interference fit.

进口圆柱轴承大多用压力机压紧或压紧。锥形孔直接安装在锥形轴上或装有衬套。

Imported cylindrical bearings are mostly pressed or pressed by presses. The tapered holes are directly mounted on the conical shaft or equipped with bushing.

文章来自：扬州SKF轴承 www.wh-skf.com

The article comes from: Yangzhou SKF bearing www.wh-skf.com

文章来自：扬州INA轴承 www.ina-china.cn

The article comes from: Yangzhou INA bearing www.ina-china.cn

文章来自：扬州NSK轴承 www.klbbearings.com

The article comes from: Yangzhou NSK bearing www.klbbearings.com

***：524085168  

电话：0510-81207777

手机：13311666672