浙江SKF轴承热感应与不同形式锥孔安装

除了使用浙江SKF轴承热油外，感应加热装置还采用电磁感应原理。

In addition to using Zhejiang SKF bearing hot oil, induction heating device also uses electromagnetic induction principle.

感应浙江SKF轴承加热装置配备有励磁线圈。在电磁感应之后，电流流向加热体（周成），并通过周成本身的阻抗产生热量。因此，可以在短时间内不用火和油均匀加热。轴承热负荷高、清洁。

Induction Zhejiang SKF bearing heating device equipped with excitation coil. After electromagnetic induction, the current flows to the heating body (Zhou Cheng) and generates heat through the impedance of Zhou Cheng itself. Therefore, it can be heated evenly without fire and oil in a short time. The heat load of the bearing is high and clean.

浙江SKF轴承内环的安装和拆卸可用于铁路车辆轴箱的滚柱轴承和圆柱滚子轴承等特殊感应加热装置。

The installation and di***antling of Zhejiang SKF bearing inner ring can be used for special induction heating devices such as roller bearings and cylindrical roller bearings for railway vehicle axle boxes.

锥形孔轴承直接将内圈连接到圆锥轴上，或使用浙江SKF轴承紧套和可拆卸套筒安装在圆柱形轴上。

Tapered bore bearings directly connect the inner ring to the conical shaft, or use the Zhejiang SKF bearing tight sleeve and detachable sleeve to install on the cylindrical shaft.

大型球面滚子浙江SKF轴承液压安装，液压螺母用来压缩套筒。在密套上设置有油孔，高压油被送入配合面，螺栓被压入固定套安装方法。

The large spherical roller is installed in Zhejiang SKF bearing hydraulically, and the hydraulic nut is used to compress the sleeve. An oil hole is arranged on the tight sleeve, the high pressure oil is sent to the mating surface, and the bolt is pressed into the fixing sleeve installation method.

浙江SKF轴承的减少是用来检查径向间隙的减少以便安装的。使用塞尺测量间隙，如图8所示，应同时测量两列的***小值。

The reduction of SKF bearings in Zhejiang is used to check the reduction of radial clearance for installation. Using the feeler gauge to measure the clearance, as shown in Figure 8, the minimum value of the two column should be measured at the same time.

当浙江SKF轴承尺寸扩大并安装在轴上时，由于外圈的椭圆变形和轴承底部的间隙，测量将大于实际间隙。径向间隙过大，误差过大，或实际安装间隙过小。因此，我们应该使用两个水平间隙A、B和底部间隙的一半作为间隙C。

When the bearing size of Zhejiang SKF is enlarged and installed on the shaft, the measurement will be greater than the actual gap due to the elliptical deformation of the outer ring and the clearance at the bottom of the bearing. The radial clearance is too large, the error is too large, or the actual installation gap is too ***all. Therefore, we should use two horizontal clearance A, B and half of the bottom clearance as gap C.

在浙江SKF轴承布什上安装滚珠轴承时，外圈可灵活调整，安装后的间隙不应太小。

When ball bearings are installed on SKF bearing Bush in Zhejiang, the outer ring can be adjusted flexibly, and the clearance after installation should not be too ***all.

大型浙江SKF轴承在受压时需要很大的力，因此很难工作。因此，热装方法广泛应用于油加热轴承、膨胀轴承和安装在轴上。该方法在安装过程中不产生力失配，缩短了操作时间。

Large SKF bearings in Zhejiang need great force when they are pressed, so it is difficult to work. Therefore, the hot charging method is widely used in oil heating bearings, expansion bearings and mounted on the shaft. The method does not produce force mi***atch during installation and shortens operation time.

文章来自：浙江SKF轴承 www.wh-skf.com

The article comes from: Zhejiang SKF bearing www.wh-skf.com

文章来自：浙江INA轴承 www.ina-china.cn

The article comes from: Zhejiang INA bearing www.ina-china.cn

文章来自：浙江NSK轴承 www.klbbearings.com

The article comes from: Zhejiang NSK bearing www.klbbearings.com