江苏NSK轴承压力安装的特殊形式

希望江苏NSK轴承包装在安装时打开。润滑脂润滑时，轴承不清洗，直接用油脂填充。当油被润滑时，不必清洗它。然而，仪器或高速轴承用清洁油清洗，以去除应用于江苏NSK轴承的防锈剂。除锈剂易生锈，不能随意放置。

It is hoped that the Jiangsu NSK bearing packaging will be opened at the time of installation. When lubricating grease is lubricated, bearings are not cleaned and filled directly with grease. When the oil is lubricated, it is not necessary to clean it. However, the instrument or high speed bearing is cleaned with clean oil to remove the rust inhibitor applied to Jiangsu NSK bearings. Rust remover is easy to rust and can not be placed at will.

此外，江苏NSK轴承润滑脂不直接清洗和使用。

In addition, Jiangsu NSK bearing grease is not directly cleaned and used.

轴承的安装方法，由于江苏NSK轴承的结构、协调、条件不同，一般由于轴的转动，所以内圈需要过盈配合。圆柱孔轴承通常用压力机压紧或加热。锥形孔直接固定在锥形轴上或装有紧套。

Bearing installation method, because Jiangsu NSK bearing structure, coordination, different conditi***, generally due to the rotation of the shaft, so the inner ring need interference fit. Cylindrical bore bearings are usually pressed or heated by a press. The tapered holes are directly fixed on the conical shaft or equipped with tight sleeves.

当安装在江苏NSK轴承座上时，经常采用间隙配合。当外圈受到干扰时，通常用压力机压或冷却。当干冰被用作冷却剂和冷缩装置时，空气中的水凝结在江苏NSK轴承表面上。因此，需要采取防锈措施。

When installed on the NSK bearing block in Jiangsu, the gap fit is often used. When the outer ring is disturbed, it is usually pressed or cooled with a press. When dry ice is used as coolant and cold shrinkage device, the water in the air condenses on the surface of NSK bearing in Jiangsu. Therefore, anti rust measures need to be taken.

小型江苏NSK轴承广泛应用于压力机上。如图1所示，垫圈固定在内圈上，并用压力机紧紧地压在内圈表面上。外圈江苏NSK轴承安装在垫圈上安装内座圈，会在跑道上造成压痕或压缩，因此严禁。

***all Jiangsu NSK bearings are widely used in presses. As shown in Fig. 1, the washer is fixed on the inner ring and pressed tightly on the inner ring surface with a press. The outer ring Jiangsu NSK bearing is installed on the washer to install the inner race, which will cause indentation or compression on the runway, so it is strictly prohibited.

另外，在操作江苏NSK轴承前，应将油涂抹到配合面上。如果需要，锤子应该放在内圈上，垫子应该放在内圈上。这种方法经常导致轴承损坏，因此仅限于小扰动。它不能用于大、中、大轴承。

In addition, oil should be applied to the mating surface before the operation of NSK bearing in Jiangsu. If necessary, the hammer should be placed on the inner ring, and the cushion should be placed on the inner ring. This method often results in bearing damage and is therefore limited to ***all disturbances. It can not be used for large, medium and large bearings.

应安装和安装江苏NSK轴承，如深沟球轴承和内外环。如图2所示，在使用内圈和外圈垫圈时，使用螺钉或油压。滚珠轴承很容易在外圈上倾斜。即使没有过盈配合，***好安装垫圈。

Jiangsu NSK bearings shall be installed and installed, such as deep groove ball bearings and inner and outer rings. As shown in Fig. 2, screw or oil pressure is used when using inner ring and outer ring washer. Ball bearings are easy to tilt in the outer ring. Even if there is no interference fit, it is best to install the washer.

可分离的轴承，如江苏NSK轴承和圆锥滚子轴承，可分别安装在轴和轴承上。当内环和外圈分开安装时，钥匙将被牢固地关闭，以防止两个中心偏离。

Separable bearings, such as Jiangsu NSK bearings and tapered roller bearings, can be installed on shafts and bearings respectively. When the inner ring and outer ring are installed separately, the key will be firmly closed to prevent the two centers from deviating.

文章来自：江苏SKF轴承 www.wh-skf.com

The article comes from: Jiangsu SKF bearing www.wh-skf.com

文章来自：江苏INA轴承 www.ina-china.cn

The article comes from: Jiangsu INA bearing www.ina-china.cn

文章来自：江苏NSK轴承 www.klbbearings.com

The article comes from: Jiangsu NSK bearing www.klbbearings.com