江苏INA轴承运转检查的详细过程

安装江苏INA轴承后，检查运行情况，检查安装是否正确。小型机械可手动旋转以确认其是否平稳旋转。由于***、***、压痕等原因，检验项目运行不畅。

After installing the INA bearing in Jiangsu, check the operation and check whether the installation is correct. ***all machinery can be manually rotated to confirm whether it is rotating ***oothly. Because of foreign matter, scar, indentation and other reas***, the inspection items are running poorly.

由于安装江苏INA轴承不当，安装空间小，安装误差大，摩擦大，扭矩过大，安装基座扭矩不稳定。如果没有异常，则可以启动电源操作。

Due to improper installation of INA bearing in Jiangsu, the installation space is ***all, installation error is large, friction is large, torque is too large, torque of the mounting base is unstable. If there is no exception, you can start the power operation.

大型江苏INA轴承机械不能手动旋转，因此空载启动后立即切断电源，检查机械空气旋转，检查是否存在振动、噪声或与旋转部件接触。

The large Jiangsu INA bearing machinery can not be rotated manually, so the power is cut off immediately after the air load is started, and the mechanical air rotation is checked to check whether there is vibration, noise or contact with the rotating parts.

江苏INA轴承功率从空载开始缓慢，在规定条件下缓慢增加到额定运行。试运行中的检查项目包括异常声音、江苏INA轴承温度变化、润滑剂泄漏或变色。如江苏INA轴承发现异常，应立即停止运行，检查机械，并进行轴承检查。如有必要，请删除E。

Jiangsu INA bearing power starts slowly from no load and slowly increases to rated operation under specified conditi***. The inspection items in the trial run include abnormal sound, temperature change of INA bearing in Jiangsu, lubricant leakage or discoloration. If the INA bearing of Jiangsu is found abnormal, it should stop operation immediately, check the machinery and carry out the bearing inspection. If necessary, please delete E.

如果江苏INA轴承错位，温度将急剧上升，将出现异常高温。其原因是润滑油过多、轴承间隙过小、安装不当、密封装置摩擦过大。当高速旋转时，江苏INA轴承结构和润滑方式的选择也是原因。

If the INA bearing of Jiangsu is misplaced, the temperature will rise sharply, and there will be an abnormal high temperature. The reason is too much lubricating oil, too ***all bearing clearance, improper installation and excessive friction of the sealing device. When high-speed rotation, Jiangsu INA bearing structure and lubrication mode choice is also the reason.

江苏INA轴承转动由***检查，具有较强的金属噪声、异常声音和不规则声音。其原因是润滑不良、轴或轴承座精度差、轴承损坏和******。

The rotation of INA bearings in Jiangsu is examined by stethoscope with strong metal noise, abnormal sound and irregular sound. The reason is poor lubrication, poor accuracy of shaft or bearing seat, bearing damage and foreign matter intrusion.

文章来自：江苏SKF轴承 www.wh-skf.com

文章来自：江苏INA轴承 www.ina-china.cn

文章来自：江苏NSK轴承 www.klbbearings.com