江苏SKF轴承受损的根源追溯

在机械的使用中，***容易出现故障的是轴承。这是因为机器本身的江苏SKF轴承是一个易碎零件，经常在恶劣环境中使用很长时间，因此经常失效和损坏。它需要解释其损坏的原因，一般分为两部分。

In the use of machinery, the most prone to failure is bearings. This is because the Jiangsu SKF bearing of the machine itself is a fragile part, often used in harsh environment for a long time, so it often fails and damages. It needs to explain the cause of its damage and is generally divided into two parts.

***点，江苏SKF轴承的不当使用

The first point, the improper use of SKF bearing in Jiangsu

1，轴承的极限转速过高。当江苏SKF轴承在高速极限环境中使用时，它将过载。此时，江苏SKF轴承接触部位之间的润滑膜变薄，摩擦阻力增大，导致轴承的高温变形和轴承损坏。为了启动轴承，应避免***。

1, the ultimate speed of the bearing is too high. When Jiangsu SKF bearing is used in high speed limit environment, it will be overloaded. At this point, the lubricating film between the contact parts of SKF bearings in Jiangsu is thinner and the frictional resistance increases, resulting in high temperature deformation and bearing damage. In order to start the bearing, overspeed should be ***oided.

2，当压力不足时，机器的内部压力在运行。机器内部压力过低会损坏整个润滑状态。这样，江苏SKF轴承就不能得到良好的润滑，导致轴承失效。

2, when the pressure is insufficient, the internal pressure of the machine is running. Too low pressure inside the machine will damage the whole lubrication state. In this way, Jiangsu SKF bearings can not get good lubrication, resulting in bearing failure.

3，当机械冰箱启动时，立即增加江苏SKF轴承的速度。机器启动后，润滑油不会对轴承表面产生良好的润滑作用。一旦润滑油的运行速度增加，润滑油的温度就会升高，这将损坏轴承的润滑状态。在这种情况下，轴承的摩擦力增大，磨损程度增加。

3, when the mechanical refrigerator starts, immediately increase the speed of Jiangsu SKF bearings. After the machine starts, the lubricating oil will not produce good lubrication on the bearing surface. Once the running speed of the lubricating oil increases, the temperature of the lubricating oil will increase, which will damage the lubrication state of the bearing. In this case, the friction force of the bearing increases and the wear degree increases.

第二点，江苏SKF轴承的不适当维护

Second point, improper maintenance of SKF bearing in Jiangsu

1。润滑油的质量。如果使用劣质或劣质润滑剂，江苏SKF轴承的润滑状态将被***，轴承将被损坏。

1. The quality of the lubricating oil. If the inferior or inferior lubricant is used, the lubrication state of Jiangsu SKF bearing will be destroyed and the bearing will be damaged.

2。注油或更换时间不合适。在机械中使用的润滑油***常见的类型是油，无论是充油还是更换。如果不能及时完成，江苏SKF轴承油的内部和润滑油就会老化。这些条件不仅会加速轴承的磨损程度，而且会造成柴油管道的堵塞。

2. Oil injection or replacement time is not appropriate. The most common type of lubricating oil used in machinery is oil, whether it is oil filled or replaced. If not completed in time, Jiangsu SKF bearing oil and lubricants will be aging. These conditi*** will not only accelerate the wear degree of the bearing, but also cause the blockage of the diesel pipeline.

文章来自：江苏SKF轴承 www.wh-skf.com

The article comes from: Jiangsu SKF bearing www.wh-skf.com

文章来自：江苏INA轴承 www.ina-china.cn

The article comes from: Jiangsu INA bearing www.ina-china.cn

文章来自：江苏NSK轴承 www.klbbearings.com

The article comes from: Jiangsu NSK bearing www.klbbearings.com