江苏SKF轴承高温下的保护措施

虽然江苏SKF轴承新技术采用整体式保持架，但材料节省和车削性能较差。一般来说，轴承的使用寿命与3个因素有关，一个是轴承本身的质量。二是利用环境。三是安装方法。

Although the new technology of SKF bearing in Jiangsu adopts integral cage, the material s***ing and turning performance are poor. Generally speaking, the service life of the bearing is related to 3 factors, one is the quality of the bearing itself. The two is to make use of the environment. The three is the installation method.

即使肉眼看不到进入轴承的面，也会增加轴承的磨损、振动和噪声。

Even if the naked eye can not see the surface of the bearing, it will increase the wear, vibration and noise of the bearing.

当用手直接握住江苏SKF轴承时，你应该洗掉手上的汗水，停止使用高质量的矿物油。在雨季和夏季，我们应注意防锈。

When holding the Jiangsu SKF bearing directly with your hands, you should wash the sweat off your hands and stop using high quality mineral oil. In the rainy season and in summer, we should pay attention to rust prevention.

那么江苏SKF轴承损坏是如何处理的呢？如果江苏SKF轴承使用得当，就可以使用，直到达到疲劳寿命。但是会有事故和无法使用的事故。相对于疲劳寿命，这种早期损伤称为失效或事故的质量极限。

Then how to deal with the damage of SKF bearing in Jiangsu? If Jiangsu SKF bearings are used properly, they can be used until fatigue life is reached. But there will be accidents and accidents that can't be used. Relative to fatigue life, this early damage is called the quality limit of failure or accident.

由于安装、使用和润滑，它们中的许多被忽略。外来***是不足以研究轴壳的热影响。轴承的损坏状态，如滚子轴承的环和边缘，可被认为是油缺乏、油结构不当、外部物体***、轴承安装误差和大挠度的原因。

Many of them are neglected due to installation, use and lubrication. External invasion is not enough to study the thermal influence of axle shells. The damaged state of the bearing, such as the ring and edge of the roller bearing, can be c***idered as the reason for the lack of oil, the improper oil structure, the intrusion of the external objects, the installation error and the large deflection of the bearing.

江苏SKF轴承的巧合和原因。因此，仅通过研究轴承损伤很难知道损伤的真正原因。但是，如果知道NSK轴承机械的使用情况、使用条件、周围高温轴承的结构，并了解事故前后的情况，结合轴承的损坏和几个原因，可以防止类似ACC的发生。ID.ROM再次出现。

The coincidences and reas*** of the SKF bearing in Jiangsu. Therefore, it is difficult to know the real cause of damage only by studying bearing damage. However, if you know the use of NSK bearing machinery, the use conditi***, the structure of the surrounding high temperature bearing, and understand the situation before and after the accident, combined with the damage of the bearing and several reas***, it can prevent the occurrence of similar ACC. ID.ROM appears again.

通过介绍，可以发现江苏SKF轴承的正确使用不受损坏，安装不正确，使用***，润滑不当，这是轴承高温损坏的主要原因，因此企业应更加重视这些。方面。使用轴承时，防止轴承轴损坏，影响工作。

Through the introduction, we can find that the correct use of SKF bearings in Jiangsu is not damaged, the installation is incorrect, the use of foreign objects, improper lubrication, which is the main reason for the high temperature damage of the bearing, so the enterprises should pay more attention to these. Aspect. When bearing is used, the bearing shaft is prevented from damaging and affecting work.

文章来自：江苏SKF轴承 www.wh-skf.com

The article comes from: Jiangsu SKF bearing www.wh-skf.com

文章来自：江苏INA轴承 www.ina-china.cn

The article comes from: Jiangsu INA bearing www.ina-china.cn

文章来自：江苏NSK轴承 www.klbbearings.com

The article comes from: Jiangsu NSK bearing www.klbbearings.com